Lock Installation in
Meyerland, Houston, TX

Most installs are planned.

Three New Doors on a Raised House, From Call to Last Test

Here's a typical lock installation in Meyerland, start to finish.

A couple had just finished rebuilding their house on a raised foundation, the third time they'd dealt with water in fifteen years and, they hoped, the last. A steel door into the storage room under the house, and a fiberglass door from the kitchen onto the raised back deck. They'd bought a handle set and deadbolt for the front and wanted simpler hardware on the other two, all on one key.

Around ten in the morning, the wife called us. The dispatcher asked what each door was made of, whether any were pre-bored, and what hardware they had. She asked for photos of the front door's edge and the handle set box, and checked the template against a standard backset. Everything would fit. She booked the technician for the next morning. He'd call once he was driving over.

The technician arrived on time, in uniform and showed his ID. He checked her license against the address. He measured each door twice. At the front door, he used his jig to bore the handle set and deadbolt holes at the spacing on the template, chiseled the latch mortises square, and set heavy strikes with 3-inch screws into the stud. At the storage room's steel door, he switched to bits made for steel and drilled slowly so the skin wouldn't tear.

The back deck door gave him the only trouble. When he drilled for the strike screws, the bit hit metal: the builder had used a steel flashing strip behind the frame. He moved the strike slightly, pre-drilled through the flashing with the right bit, and drove the screws into solid wood. The bolt seated fully.

He keyed all three locks to one key with his pinning kit and cut five copies. Then he tested each lock from both sides with the doors closed and the weatherstrip compressed. All three threw cleanly.

His neighborly advice: on raised homes, the storage door underneath is often forgotten, so lock it like it matters.

Fitting Locks to New Doors, Step by Step

Measure Twice

Door thickness, backset, bore size and handle set spacing all have to match the hardware. We measure first and check your hardware against the door before drilling, so a brand-new door never ends up with extra holes or a visible patch under the trim.

Blank Doors From the Builder

Blank doors need a face bore, an edge bore and latch and strike mortises. New door lock installation with a proper jig keeps everything square, so the latch slides smoothly and the deadbolt throws its full inch without dragging on the strike.

Install Deadbolt and Knob as a Matched Pair

When we install deadbolt and knob or lever on the same door, we bore both at the right spacing and key them alike, so they look and work as a set. On handle sets, we follow the template exactly, because the thumb latch and the deadbolt have to line up.

Keyed Alike Locks Across the House

Keyed alike locks let one key open every exterior door, including storage rooms under raised homes and deck doors. It means fewer keys to carry, fewer copies to track and a simpler rekey later.

Raised Homes and Lower-Level Doors

Storage rooms and garages under raised homes often get basic doors and little thought about locks. They hold tools, bikes and sometimes access to the stairs.

Skins, Cores and Slower Drilling

Steel and fiberglass doors need different bits and slower drilling than wood. Done right, they hold locks well and resist humidity better than wood. Done badly, the skin tears or the foam core crushes, and the lock never feels solid.

Hidden Metal in New Frames

New frames sometimes have steel flashing or brackets behind the trim. We adjust, pre-drill with the right bit, and make sure the strike screws reach solid wood rather than stopping in a thin strip of metal.

Hardware You've Already Bought

Send us the model and a photo of the door first. If it fits, we'll install it. If it won't, we'll tell you before the visit and suggest something similar that will.

Door Hardware Installation for Offices

Small offices and clinics near Meyerland use keyed levers on storage rooms, records rooms and back doors. Door hardware installation for businesses uses commercial-grade parts built for heavier daily use.

Owners, Builders and Tenants

Owners can book directly, and builders can book on an owner's behalf with written permission. Tenants need written landlord approval. We check ID against the address before drilling.

Tested Before We Leave

Every lock is tested from both sides with the door closed and the weatherstrip compressed. A lock that works only with the door open isn't installed properly, and we won't leave it that way.

Meeting You at the Spot in Meyerland

Service covers all of Meyerland, and the dispatcher confirms your address on the call. Installs are booked at a time that suits you. Mornings after school drop-off are the easiest time in Meyerland; the 610 Loop near Beechnut and the Braeswoods at pickup time are slow.

Careful, Neighborly Technicians

Expect a uniformed technician carrying company ID. They measure twice, explain what they're installing and why, protect new floors and finishes, and clean up their shavings. On a freshly rebuilt house, they treat every surface as if it were just painted, because it probably was.

Fast Locksmith 24/7 is licensed and insured, and homeowners give us 5 stars on Google.

Lock Installation Around Meyerland

Lock installation in Meyerland comes from raised and rebuilt homes with blank new doors, renovated ranch houses with new entries, storage rooms and garages under raised homes, duplexes, and small offices along Beechnut. Lock installation in Meyerland starts with a tape measure and a photo. Owners finish the hardware themselves; we're glad to be that last step. If you need a locksmith to install locks on a new door, have the hardware and the door ready, and we'll do the rest.

A new lock starts with the door. Tell us what it is made of and how thick it is. Older solid-wood doors, hollow-core doors and steel doors all need different bits and care.

Placement matters. Height, spacing from the edge and the position of the strike change how the lock feels every day. We follow standard measurements and adjust for your door.

For raised homes with a landing, ask us about weather protection. A lock exposed to rain and sun lives a shorter life.

If you are installing locks on a new gate, shed or workshop, tell us what is inside. A tool shed and a storage room for family keepsakes call for different hardware.

Ask for spare strike plates and longer screws. They are small items that come in handy.

When we finish, we test the lock together. Lock it, unlock it and push on the door.

Tell us if the door will be used by children, older relatives or anyone with limited grip. Lever handles and larger thumb turns can make daily use easier.

If you have a storm door or screen door in front of the main door, mention it. The handle position and the swing can affect which lock fits best.

Ask about the screws that come with the kit. Short ones hold the strike to the trim only, and longer ones reach the stud behind it.

We also install locks in Bellaire, West University Place and Westchase. For deadbolts specifically, see deadbolt installation, and to replace worn hardware, see lock replacement.