Installations are usually scheduled. If a door can't be secured, a technician comes.
A calm note from the dispatcher: if a hole went wrong, stop drilling. We can usually repair it with a sleeve or a larger plate.
A Hole Too Big, a Hole Saw and a New Door That Wouldn't Hold a Lock
The first fix people try often makes the second one harder. Here's a typical example from a house off Will Clayton Parkway.
A homeowner replaced the side door of his garage with a new steel one and bought a deadbolt at a hardware store to match. He read the instructions and used a hole saw on the new door, but the saw wandered. The hole came out oval and slightly large. When he installed the deadbolt, it wobbled in the opening. He tried shimming it with cardboard, which held for a day.
He called us around eleven in the morning, standing in the garage with the deadbolt in one hand and the hole saw in the other. A neighbor had walked over after hearing the saw wander off and stayed, arms folded, offering opinions about cardboard shims. The new door sat open on its hinges, swinging a little in the breeze. Our dispatcher kept her tone even. Was he safe and was the door secure now? He had propped a board against it. Was it a steel door? Yes. What brand of deadbolt? She noted it. She explained that an oval hole in steel can be repaired with a reinforcing plate that covers the opening, and that the technician would check the door's edge bore too. She said a technician was heading over.
The technician arrived in uniform and showed his ID, then checked the man's license against the address. He looked at the hole and measured it. The first attempt to fit a reinforcement plate didn't seat; the hole was too far off center. He used a jig and a new hole saw to open a clean bore a size up, then fitted a larger reinforcement ring that covered the damage. The deadbolt went in snugly on the second try.
He drilled the edge hole with a jig, set the strike with 3-inch screws and tested the bolt, which threw fully. The homeowner looked at the old hole and laughed. He said he'd bought the hole saw for exactly this job and had never expected it to be the problem. The technician told him the saw was fine; it just needed the jig to hold it steady. The dispatcher's advice: for a new door, have the bores cut by someone with a jig.
Fitting Locks to New and Replaced Doors
Drilled the Hole Too Big
If you drilled the hole too big, don't keep going. A reinforcement plate or sleeve often saves the door.
Fix a DIY Door Bore
To fix a DIY door bore, we measure, correct the opening and fit hardware that covers the repair.
A Fresh Slab and Where to Drill It
To install lock on new door slabs, we cut the bores and edge hole with a jig and set the latch and strike.
Door Prep for Locks
Door prep for locks means a clean bore, a square edge hole and a mortise for the latch face.
An Installer With a Jig on the Van
A lock installer near me visit brings jigs, hole saws and hardware on the van.
Steel Slabs and Their Bits
Steel doors need the right bits and a steady hand. We use jigs and reinforcement rings.
Three-Inch Screws Where the Bolt Lands
Short screws are the weak point. We use 3-inch screws into the framing.
ID and Address
Photo ID with the address, or a lease, deed or bill.
Matching Your Other Locks
New locks can be keyed to match your existing ones.
Sheds, Gates and Detached Garages
Outbuildings often have basic locks. We fit stronger hasps and deadbolts and key them to the house if you like.
Remodel Doors and Patio Entries
Remodels add doors that need locks. We prepare the slab and install hardware to match the rest of the house.
Prehung Doors and Fresh Frames
A prehung door often arrives with the strike and bore marked. We use those marks, then confirm them with a jig.
Pet Doors and Door Sweeps
A new door often gets a sweep or a pet door. We install the lock so neither interferes with the latch or the bolt.
Meeting You at the Spot in Atascocita
The dispatcher takes your address in Atascocita, and a technician is sent to that exact spot. Installs are booked at a time that suits you. Homes near FM 1960, Will Clayton Parkway and the lake are on our routes. A weekday morning visit works well for most installs, with the lock ready by lunch.
Calm Technicians With a Jig
A technician in our company uniform arrives and shows photo ID first. He measures twice, drills once and tests the door before he leaves. He'll check that the door swings freely and latches without catching on the frame. He'll make sure the new lock doesn't interfere with the door's weatherstripping or sweep.
Homeowners around Houston rate Fast Locksmith 24/7 5 stars on Google, and we're licensed and insured.
Lock Installation Calls Around Atascocita
Installation calls in Atascocita come from owners of new doors, remodelers, families adding a lock to a shed and DIYers who need a hand. Lock installation in Atascocita often follows a hole that came out wrong.
Atascocita keeps growing, and with it comes steady work for people who build and remodel. New doors go into additions, garage conversions, patio entries and sheds. Each one needs a lock, and each lock needs a bore that is cut square, an edge hole that is centered and a strike set with long screws into the frame.
Homeowners who hang their own doors call after the saw wanders or the holes come out wrong. Both are routine. We use a jig to hold the saw steady, and we carry reinforcement rings and sleeves for the cases that need them.
Our technicians also coordinate with painters and finish carpenters, since a lock installed before the final coat is a lock that may need to come off again. If you're working with a crew, tell the dispatcher the schedule, and we'll plan around it.
Atascocita's builders and remodelers work through the summer heat, and a door that arrives on a Friday often needs a lock by Monday. For custom or specialty doors, the technician can look at the slab first and order what's needed.
New locks and new doors work best when installed together. If you're replacing a door, tell the dispatcher before you order hardware; our technicians can advise on bore size, backset and edge preparation so the pieces match. A short phone call can prevent a trip back to the store.
If you're hanging the door yourself, leave the lock bores for us. A door that's already been drilled badly is harder to fix than one we start fresh.
A new lock starts with the door. Tell us what it is made of and how thick it is. Solid wood, hollow-core and steel doors all take different tools.
Placement matters. Height, spacing from the edge and the position of the strike change how the lock feels each day.
Tell us if the door will be used by children, older relatives or anyone with limited grip. Lever handles make daily use easier.
Ask for spare strike plates and longer screws. They are small items and useful later.
Keep the instruction sheet and the spare keys together in a folder.
We install locks in Humble, Kingwood and Channelview too. For replacing old hardware, see lock replacement; for keypads, smart lock installation.
Estimated Technician Arrival Time
Arrival times vary depending on your location and technician availability.
Actual arrival time may vary depending on your exact location, traffic conditions, time of day, current demand, and technician availability.
Providing your exact vehicle location when calling allows us to give you a more accurate estimated arrival time.